Replacing the floor in one room is a weekend decision. Replacing floors across the whole house is a bigger project. You're choosing materials that have to work in very different rooms, budgeting for problems you can't see yet, and living around a crew for days or weeks.
This guide walks you through it in plain English. You'll see how hardwood, vinyl, laminate and tile compare, which floors suit which rooms, and why the subfloor matters more than most people expect. We also cover how a whole-home installation runs, what drives the cost, and how to care for each floor so it lasts.
Key takeaways
No single floor is best everywhere. Many homes use wood or wood-look planks in living areas and water-tolerant flooring in bathrooms, laundry rooms and basements.
The subfloor decides whether the new floor lasts. It has to be flat, dry and stiff enough for the material going on top.
Removal and prep are real costs. Tear-out, disposal, subfloor repair and trim work can add thousands to a whole-home quote.
Older homes need a hazard check first. Old vinyl tile, flooring adhesive and painted trim can contain asbestos or lead.
Upkeep comes down to water, grit and the right cleaner. The wrong mop or doormat can damage a floor faster than daily traffic.
Replace, refinish or cover? Start here
Not every tired floor needs to come out. Figure out what you actually need before you price new flooring.
Solid hardwood can often be refinished instead. Sanding and refinishing removes surface wear and lets you change the color. NerdWallet puts refinishing at $1,100 to $2,700 on average and notes that replacement usually costs at least twice as much. Engineered hardwood is more limited. Depending on the thickness of its top wood layer, it may only take one or two refinishes.
Replacement makes sense when:
Boards are cupped, buckled or water-stained deep into the wood
Vinyl or laminate is peeling, gapping or swollen at the seams
Tile is cracked in several places or keeps coming loose
You want a different material, not just a fresh finish
The floor feels soft, bouncy or spongy underfoot
Take that last sign seriously. A spongy or uneven floor can point to damage in the subfloor or joists. Have it checked before you choose new flooring, because the repair may need to happen first.
Flooring materials compared
Here's how the main options stack up. The sections below explain each one.
Material | Handles water | Can be refinished | Feel underfoot | Good fit for |
Solid hardwood | Poor | Yes, several times | Warm, natural | Living rooms, dining rooms, bedrooms, hallways |
Engineered hardwood | Fair | Limited (depends on top layer) | Warm, natural | Same as solid, plus some basements |
Luxury vinyl (LVP/LVT) | Very good | No | Softer and quieter than tile | Kitchens, basements, laundry rooms, whole-home use |
Laminate | Fair (varies by product) | No | Firm, can sound hollow | Living areas, bedrooms, some kitchens |
Porcelain/ceramic tile | Excellent | No (grout can be refreshed) | Hard and cool | Bathrooms, entries, laundry rooms, kitchens |
Carpet | Poor | No | Softest, warmest | Bedrooms, family rooms |
Solid hardwood
Solid hardwood is milled from single pieces of wood. It ages well, it can be sanded and refinished several times, and buyers recognize it.
The trade-off is movement. Wood swells as it absorbs moisture and shrinks as it dries. For that reason, the National Wood Flooring Association (NWFA) says solid wood suits floors on or above ground level, but not below grade. Its guidelines offer a handy test: if the soil outside sits 3 inches or more above a floor level, treat that level as below grade.
Pros: long life, can be refinished, natural look, strong resale appeal
Cons: sensitive to water and humidity, dents and scratches, higher cost
Engineered hardwood
Engineered hardwood has a real wood top layer bonded to a plywood or composite core. You get the look of hardwood with more stability. Many engineered products are rated for installation above, on or below grade.
The surface is still wood, so it still dislikes standing water. Manufacturers such as Shaw advise against installing hardwood flooring in bathrooms.
Pros: real wood surface, more stable than solid wood, works over concrete and in some basements
Cons: limited refinishing, quality varies widely between products
Luxury vinyl plank and tile (LVP/LVT)
Luxury vinyl is a layered plastic floor with a printed design under a clear wear layer. Rigid-core versions click together and "float" over the subfloor without fasteners. Many are sold as waterproof, which is a big reason LVP has become a popular whole-home choice.
Waterproof planks don't make the room waterproof, though. Water can still reach the subfloor through edges and gaps. Vinyl also can't be refinished. Once the wear layer is badly scratched or worn through, the plank has to be replaced.
What to compare between products: wear layer thickness (measured in mils), core type, whether underlayment comes attached, and warranty terms for the rooms you plan to use it in.
Pros: water-tolerant, comfortable, budget-friendly, DIY-friendly in simple rooms
Cons: can't be refinished, can fade in strong sun, can be stained by rubber-backed mats
Laminate
Laminate is a printed wood image over a dense fiberboard core. Its surface is tough and resists scratches well. The core is the weak spot. Water that sits on the seams can make it swell. Some newer products are rated water-resistant, so check the specs if you're considering laminate for a kitchen.
Pros: scratch resistant, often lower cost, easy click installation
Cons: core can swell with water, can't be refinished, can sound hollow without good underlayment
Porcelain and ceramic tile (and natural stone)
Tile handles water better than any other option here, and it lasts a long time on a solid base. Porcelain is denser than standard ceramic. Natural stone such as marble or slate looks beautiful but needs a stiffer floor structure and more upkeep.
Tile doesn't tolerate movement. A floor that flexes too much will crack tile or grout. The subfloor section below explains what that means in practice.
Pros: handles water, very durable, easy to clean
Cons: hard and cold underfoot, slower and costlier to install, grout needs care
Carpet
Carpet remains common in bedrooms because it's soft, warm and quiet. It's also the hardest to keep clean and a poor choice anywhere water shows up.
A health note on wood-based floors
Laminate and many engineered floors contain composite wood made with adhesives. Under the federal TSCA Title VI rule, regulated composite wood products made in or imported into the U.S. after March 22, 2019, must be labeled as compliant with EPA's formaldehyde emission standards. Look for "TSCA Title VI compliant" on the box or ask your supplier.
Choosing flooring room by room
Each room puts different demands on a floor. Use this table as a starting point, then adjust for your household.
Room | What matters most | Strong choices | Use caution with |
Kitchen | Spills, dropped items, heavy traffic | LVP, porcelain tile, engineered hardwood (with care) | Solid hardwood near the sink, basic laminate |
Bathrooms | Water, slip resistance | Porcelain or ceramic tile, LVP | Any hardwood, carpet, laminate |
Basement | Moisture from the slab, humidity | LVP, tile, engineered products rated for below grade | Solid hardwood, carpet without moisture control |
Living and dining rooms | Look, comfort, wear | Hardwood, engineered, LVP, laminate | Very soft wood species in busy homes |
Bedrooms | Comfort, quiet | Carpet, hardwood, engineered, LVP | Hard tile without rugs |
Entry, mudroom, laundry | Grit, water, wet shoes | Porcelain tile, LVP | Hardwood without mats, laminate |
Stairs | Safety, durability | Hardwood treads, carpet | Slick finishes, products without matching stair nosings |
Kitchens
Kitchens take spills, dishwasher drips and dropped pans. LVP and tile handle that best. If you want wood in an open-plan kitchen, engineered hardwood is more stable than solid. Keep a mat by the sink and wipe up water quickly. To see how flooring fits into a full kitchen budget, read our guide to kitchen remodeling costs.
Bathrooms
Bathrooms are where tile earns its place. When you shop, ask about slip resistance. Under the ANSI A137.1 tile standard, tile for level indoor floors that will be walked on when wet should have a wet DCOF (dynamic coefficient of friction) of 0.42 or higher. No tile is truly slip-proof, so a matte or textured finish helps. Smaller tiles add more grout lines, which also improve grip. If the floor is part of a bigger bathroom project, our breakdown of bathroom remodeling costs shows how flooring fits alongside fixtures, labor and permits.
Basements
Basement floors sit on concrete that can release moisture all year. Choose a floor that tolerates it, such as LVP, tile or an engineered product rated for below grade, and test the slab before installation (see below).
One floor everywhere, or a mix?
Running one floor through the whole house looks clean and avoids height changes at doorways. It works best with a material that suits every room, which usually means LVP, or engineered wood if you keep it out of full bathrooms.
Mixing materials lets you spend where it shows and use tougher flooring where it's needed. Hardwood in living areas with tile in the bathrooms is a common pairing. If you mix, plan transitions early. Products come in different thicknesses, and a badly planned height change becomes a trip hazard.
The subfloor: the part nobody sees
The subfloor is the structural layer under your finished floor. In most homes it's plywood or OSB panels over wood joists, or a concrete slab. Many flooring failures trace back to it. Installers judge a subfloor on three things.
1. Is it flat enough?
Flat isn't the same as level. Flat means no humps or dips. Rigid vinyl planks are especially demanding, and many manufacturers require the subfloor to be flat within 3/16 inch over 10 feet. If it isn't, gaps can open at the joints. Installers grind or sand down high spots and fill low spots with leveling compound.
2. Is it dry enough?
Wood subfloors. Wood flooring and the subfloor beneath it should have similar moisture content. NWFA guidelines call for no more than a 4 percent difference for strip flooring under 3 inches wide, and no more than 2 percent for wider boards. Your installer should measure both with a moisture meter. Acclimation isn't a fixed number of days. It's the time it takes for the flooring to adjust to the conditions in your home.
Concrete slabs. Flooring and adhesive manufacturers generally require moisture testing before installation over concrete. A common method, ASTM F2170, measures relative humidity inside the slab using probes. Acceptable limits vary by product, so compare the test result with the spec sheet for the floor you're buying.
Crawl spaces. Many vinyl manufacturers require wood subfloors over a crawl space to sit at least 18 inches above the ground, with cross-ventilation and a vapor barrier over the soil.
3. Is it stiff enough?
This matters most for tile, because tile and grout can't flex. Tile industry guidelines limit floor deflection to L/360 for ceramic and porcelain tile and L/720 for natural stone, where "L" is the joist span. In simple terms, a stone floor should bend only half as much as a floor built for ceramic tile.
Joist spacing makes a big difference. With joists 24 inches apart, even 3/4-inch plywood often isn't stiff enough for tile without extra reinforcement. If you're planning tile on an upper floor or over a long span, ask your contractor how they've confirmed the floor can handle it.
Can new flooring go over the old floor?
Sometimes. It depends on what's there and what's going on top.
Many vinyl plank products can go over one well-bonded layer of existing vinyl, or over flat ceramic tile once wide grout joints are filled.
Carpet and cushioned vinyl aren't suitable bases for hard flooring.
Every layer you keep adds height, which affects doors, transitions, stairs and appliances.
Covering the old floor can save money and avoid disturbing hazardous materials. It also hides whatever is wrong underneath. If the old floor is loose, damaged or sitting on a soft subfloor, it should come out.
Safety check for older homes: asbestos and lead
This step is easy to overlook, and it can change your plan and budget.
Asbestos. Older vinyl floor tiles, the backing on old sheet vinyl and some flooring adhesives can contain asbestos. The EPA's guidance on protecting your family from asbestos says not to sand or try to level asbestos flooring or its backing, and to install new flooring over it when possible. The EPA also suggests a professional inspection if you're planning a remodel that could disturb these materials. You can't identify asbestos by looking. Old 9-by-9-inch floor tiles and black adhesive under a top layer are well-known warning signs, so have a professional test them before any tear-out begins.
Lead paint. Removing baseboards and shoe molding in a home built before 1978 disturbs painted surfaces. Under EPA's Renovation, Repair and Painting (RRP) Rule, contractors in pre-1978 homes must be certified and follow lead-safe work practices when they disturb more than six square feet of interior painted surfaces. A whole-home flooring job can cross that line quickly. Ask whether your contractor is a Lead-Safe Certified firm.
How whole-home flooring installation works
Every job is different, but a well-run whole-home replacement usually follows this order.
Measure and order. The installer measures every room and adds extra material for cuts and waste, often 5 to 10 percent. Herringbone and diagonal patterns need more. Order all material from the same production lot so the color matches, and keep a box of spares for future repairs.
Condition the materials. Wood products sit in the home, with heating or cooling running, until their moisture content suits the house. Follow the manufacturer's instructions for vinyl and laminate too.
Prepare the house. Furniture comes out. Appliances are disconnected and moved. Toilets come up in bathrooms, and some doors come off their hinges.
Check for hazards, then remove the old floor. Complete any asbestos and lead checks before demolition. Removal creates dust, so the crew should seal the work area off from the rest of the house.
Repair and prepare the subfloor. Squeaky panels are screwed down, damaged sections replaced, high spots ground down, low spots filled and moisture tested.
Install underlayment or a moisture barrier. What goes down depends on the flooring and the subfloor. Some LVP has a pad attached. Tile often needs cement board or a membrane.
Install the flooring. The method depends on the product (see the table below).
Finish the edges. Baseboards or quarter-round cover expansion gaps. Transition strips go at doorways and where materials meet. Doors are trimmed if the new floor is taller.
Cure, clean and inspect. Grout and adhesives need time to cure before heavy use. Walk through each room with your contractor and list anything that needs fixing before final payment.
Common installation methods
Method | How it works | Typical materials |
Nail-down or staple-down | Boards are fastened to a wood subfloor | Solid hardwood, some engineered |
Glue-down | Flooring is bonded with adhesive | Engineered hardwood, glue-down vinyl, wood over concrete |
Floating | Planks lock together and rest on underlayment, not fastened down | LVP, laminate, some engineered |
Thinset mortar | Tiles are set in cement-based mortar, then grouted | Porcelain, ceramic, stone |
Mistakes to avoid on a whole-home job
Don't trap a floating floor under cabinets or an island. Floating floors need room to expand and contract. NWFA guidance and many rigid vinyl manufacturers say to install fixed cabinets and islands first, then run the floating floor up to them with the required gap.
Don't trap the dishwasher. If new flooring runs up to the front of the dishwasher but not under it, the finished floor ends up higher than the spot where the dishwasher sits. It may not slide out later for repairs. Measure from the floor to the underside of the countertop before installation, and plan for flooring (or a matching spacer) under the appliance.
Check every door. A thicker floor can stop interior doors from swinging freely. Exterior doors and thresholds need extra care so they still seal against weather.
Plan stairs and landings early. Stairs usually need matching treads and nosings, and they cost more per foot than flat floor.
Watch height changes. Where two materials meet, keep the height difference small and use the right transition strip. This is a safety issue, not only a looks issue.
Can you live at home during the work?
Often, yes, especially if the crew works in phases. Plan around the kitchen and bathrooms, since those rooms are hard to live without. Some families stay elsewhere for part of the job, usually because of sanding dust and finish fumes when wood is finished on site.
Do you need a permit?
Usually not for the flooring itself. Many U.S. cities and counties follow the International Residential Code, which exempts finish work such as tiling and carpeting from building permits. Structural work is different. Replacing joists, changing floor framing or moving plumbing can require a permit. Rules vary, so check with your local building department.
Contractor licensing also varies by state and city. In New York City, for example, the Department of Consumer and Worker Protection requires a Home Improvement Contractor license for residential home improvement work costing more than $200. Check your local requirements before you sign a contract.
How much does whole-home flooring replacement cost?
There's no honest single number. Square footage and material set the baseline. What's under the old floor, and how much of it has to come out, can move the total a lot. Local labor rates do the rest. Use these ranges to plan, then get written quotes.
Cost per square foot by material
Published ranges vary, so the table shows two. The first comes from Angi's flooring cost guide, which lists average costs per square foot. Angi doesn't say whether these include labor, and it puts installer labor alone at $0.60 to $4 per square foot. The second column shows installed planning ranges published by flooring retailer BuildDirect in 2026.
Material | Angi average (per sq. ft.) | BuildDirect installed, 2026 (per sq. ft.) |
Solid hardwood | 6–25 | About 12–25+ |
Engineered hardwood | 4.50–16 | About 8–20 |
Vinyl / LVP | 2–14 | About 5–12 (LVP) |
Laminate | 3–13 | About 5–12 |
Tile | 15–20 | Not listed |
Carpet | 3.50–11 | Not listed |
For a whole-house view, HomeAdvisor's 2024 cost guide estimated $16,500 to $67,730 to refloor a typical 2,300-square-foot home.
Extra costs in whole-home quotes
These items are easy to miss when you compare prices.
Item | Typical range |
Removing old flooring | 1.50–3.50 per sq. ft. |
Subfloor replacement | 3–10 per sq. ft. |
Underlayment | 0.50–5.40 per sq. ft. |
Stairs | 11–160 per step |
Furniture moving (if hired out) | 60–120 per hour |
Mold remediation | 10–25 per sq. ft. |
Subfloor repair after water damage | 1,000–3,000 (NerdWallet) |
Floor joist repair | 40–60 per sq. ft. (NerdWallet) |
Figures are from Angi unless marked otherwise.
A sample whole-home budget
Here's a rough illustration using the ranges above. It is not a quote. It assumes 1,800 square feet of floor in a 2,000-square-foot home, with BuildDirect's installed ranges for wood and LVP and Angi's tile range.
Area | Size | Assumed rate (per sq. ft.) | Estimated range |
Living areas, halls, bedrooms (engineered hardwood) | 1,400 sq. ft. | 8–20 | 11,200–28,000 |
Kitchen and laundry (LVP) | 250 sq. ft. | 5–12 | 1,250–3,000 |
Two bathrooms (tile) | 150 sq. ft. | 15–20 | 2,250–3,000 |
Old flooring removal | 1,800 sq. ft. | 1.50–3.50 | 2,700–6,300 |
Subfloor repair allowance | 100 sq. ft. | 3–10 | 300–1,000 |
Subtotal | 17,700–41,300 | ||
With 10% contingency | 19,470–45,430 |
Use LVP instead of engineered hardwood in the living areas (5–12 per square foot) and the same home comes to about $14,850 to $33,110 with contingency. Stairs, new baseboards and appliance work would be extra.
Why include a contingency? Nobody can see the subfloor until the old floor is up. BuildDirect suggests setting aside about 5 percent when the floor and subfloor have been inspected and about 10 percent when some unknowns remain. Plan for more in older homes, after water damage, with several layers of old flooring or over untested concrete.
How to compare quotes
Ask every contractor to itemize the same things. Otherwise you're comparing guesses.
Flooring product name and quantity, including the waste allowance
Removal and disposal of each existing floor type
Subfloor repair: a per-square-foot rate or allowance, and who approves extra work
Moisture testing and floor leveling
Underlayment, moisture barrier or tile backer board
Transitions, thresholds and stair parts
Baseboards or quarter-round: reuse, replace or paint
Moving furniture and appliances, and removing and resetting toilets
Door trimming
Cleanup, cure times and a room-by-room schedule
Hazard testing and who is responsible for it
Workmanship warranty, separate from the manufacturer's product warranty
Ways to save without cutting corners
Put premium flooring in the rooms people see most and durable mid-range products elsewhere.
Install over a sound existing floor where the manufacturer allows it.
Move the furniture yourself.
Ask whether pricing the whole house as one job costs less than doing rooms separately.
Don't skip subfloor prep to save money. It's the costliest shortcut you can take.
Long-term upkeep by flooring type
Good care keeps a floor looking its best and protects your warranty. Your product's care guide comes first, since manufacturers' rules differ.
Hardwood and engineered wood
Keep grit off. Sand and grit act like sandpaper underfoot. Sweep or dust-mop often, vacuum regularly with a hard-floor setting, and clean periodically with a product made for wood floors.
Skip wet mops and steam mops. NWFA warns that both can damage the finish and the wood over time.
Control indoor humidity. NWFA recommends keeping your home between 60 and 80°F and 30 to 50 percent relative humidity all year. A humidifier during dry winters helps prevent gaps between boards.
Use felt pads and rugs. Put felt pads under furniture legs and rugs at entries and in busy work areas.
Recoat before you refinish. A light screen-and-recoat refreshes the top finish before wear reaches the wood.
Luxury vinyl
Use a pH-neutral cleaner. Manufacturers such as Shaw warn against abrasive cleaners and products containing ammonia or vinegar, which can damage the surface.
Choose the right doormats. Rubber-backed mats can leave a permanent yellow stain on vinyl that only replacement will fix. Look for mats labeled non-staining.
Block strong sun. Blinds, curtains or UV window film help prevent fading.
Protect against heavy furniture. Use wide furniture glides and never drag appliances across the floor.
Laminate
Clean with a barely damp mop or a laminate-specific spray. Water left on the seams is the main risk.
Wipe up spills right away.
Use felt pads to prevent scratches and dents.
Tile and grout
Seal cement-based grout. Sanded and unsanded grout are porous and should be sealed. Epoxy grout doesn't need sealing. Follow the grout manufacturer's guidance on how often to reseal.
Seal natural stone as the supplier recommends, and use stone-safe cleaners. Acidic cleaners can etch marble and limestone.
Repair cracked grout early so water can't reach the layers below.
Hiring a flooring contractor
A whole-home floor is a big job to hand over. Before you sign, ask:
Are you licensed where I live? Requirements vary by state and city. Look up the license yourself on the official site.
Do you carry liability insurance and workers' compensation? Ask for certificates.
Will your own crew do the work, or subcontractors?
How will you check the subfloor for flatness and moisture? Good answers mention tools and measurements, not just "we'll take a look."
Is your firm EPA Lead-Safe Certified? This matters if your home was built before 1978.
How do you handle surprises? You want a written change-order process, with pricing agreed before extra work starts.
What's your workmanship warranty? Also ask whether the installation will follow the manufacturer's instructions, so the product warranty stays valid.
When you're ready to compare local pros, browse home improvement contractors on ProsVetted. Use the questions above with every company on your shortlist.
Frequently asked questions
What is the best flooring for a whole house?
It depends on your home and household. Luxury vinyl plank is a popular single-floor choice because it handles kitchens, bathrooms and basements. Engineered hardwood works in most rooms if you keep it out of full bathrooms. Many homeowners mix materials by room.
How much does it cost to replace flooring in a whole house?
Size, materials and prep work drive the total. HomeAdvisor's 2024 guide estimated $16,500 to $67,730 for a typical 2,300-square-foot home. Our 1,800-square-foot example above ranges from about $15,000 with LVP to about $45,000 with engineered hardwood, including a contingency.
How long does whole-home flooring installation take?
It depends on square footage, material and prep work. Floating floors usually go in fastest. Tile and site-finished hardwood take longer because of curing and finishing time. Subfloor repairs, moisture problems or hazardous-material removal can extend the schedule. Ask each contractor for a room-by-room timeline.
Should I remove old flooring or install over it?
Remove it if it's loose, damaged or sitting on a soft subfloor, or if the new product requires a bare subfloor. Some products can go over one sound layer of vinyl or flat tile. If the old floor may contain asbestos, the EPA recommends covering it rather than disturbing it when possible.
Can I put hardwood in a basement?
Not solid hardwood. Some engineered hardwood is rated for below-grade use with proper moisture control, while LVP and tile are usually safer choices.
Is luxury vinyl plank really waterproof?
The planks resist water well, but water can still get underneath at the edges and seams and damage the subfloor. Wipe up spills, fix leaks quickly, and seal around tubs and showers as your installer recommends.
Does new flooring need a permit?
Often not, because flooring is usually treated as finish work. Structural repairs and plumbing changes can need permits, so confirm with your local building department.
Should flooring go in before or after kitchen cabinets?
For floating floors, install cabinets and islands first so the floor isn't pinned down. For nail-down floors, glue-down floors and tile, either order can work. Either way, plan the height of the dishwasher opening.
Does new flooring add value to a home?
New floors can make a home more appealing to buyers, especially when they replace worn or dated flooring. How much value they add depends on your local market and the material, so treat resale value as a bonus, not a guarantee.
Conclusion
A whole-home flooring replacement goes smoothly when decisions happen in the right order. Choose materials room by room. Make sure the subfloor is flat, dry and stiff enough for what's going on top. Check older homes for asbestos and lead before anything is torn out. Then compare itemized quotes with a contingency built in.
Follow those steps and your new floors have the best chance of looking good for years. When you're ready to talk to installers, take this guide with you and ask the hard questions. A good contractor will welcome them.
